Vaillant F.28: Ignition Failure on Start-Up
What the Vaillant F.28 error code means, what causes it, and why it's a job for a licensed BC gas technician — not a DIY reset.
Severity
High — needs prompt professional attention
Gas safety first
This fault involves gas, combustion or venting. If you smell gas (rotten-egg odour), hear hissing, or feel unwell, leave the building immediately and call 911 or FortisBC at 1-800-663-9911 from outside. Do not flip switches or relight anything. For all other cases, switch the boiler off and call a licensed gas technician.
What the Vaillant F.28 error code means
The boiler tried to light at the start of a heating or hot-water demand and failed after repeated attempts, so it locked out.
On Vaillant ecoTEC plus and ecoTEC exclusive condensing boilers & combis, F.28 is a ignition fault. It is a protective response — the boiler is telling you something needs attention, and the safe, lasting fix is a proper diagnosis rather than repeated resets.
Symptoms you may notice
- No heat or no hot water
- Boiler attempts to fire (you may hear clicking) then locks out
- Repeated lockouts after a few ignition attempts
Common causes of Vaillant F.28
Why this is not a DIY fix
Ignition faults sit at the intersection of the gas valve, igniter, flame-sensing electrode and gas supply. In British Columbia, diagnosing or adjusting any of these is gas-fitter work — it requires combustion analysis and manometer gas-pressure testing that, by law, only a licensed gas technician (TSBC-certified) may perform. Repeated DIY reset attempts can flood the combustion chamber with unburned gas.
In British Columbia, gas work must be performed by a TSBC-licensed gas fitter. GasBoilers.ca — a CanroHeat division — sends Red Seal–certified, gas-licensed technicians who diagnose the true cause, repair it correctly, and verify safe operation before they leave.
How our technicians diagnose & repair it
- 1Verify incoming gas supply and lock-up/working gas pressure with a manometer
- 2Inspect and clean the igniter and flame-sensing electrode, checking the spark gap
- 3Test the gas valve operation and ignition control sequence
- 4Run a full combustion analysis to confirm a safe, clean flame after repair
Related Vaillant codes
Vaillant F.28 — FAQ
What does the Vaillant F.28 error code mean?
The boiler tried to light at the start of a heating or hot-water demand and failed after repeated attempts, so it locked out. On Vaillant ecoTEC plus and ecoTEC exclusive condensing boilers & combis, this is categorised as a ignition fault.
What causes Vaillant F.28?
The most common causes are: No or low gas supply (check other gas appliances and the meter); Worn ignition or flame-sensing electrodes; Faulty gas valve; Air in the gas line after work. A licensed technician confirms which one applies before any part is replaced.
Can I fix Vaillant F.28 myself?
No. Ignition faults sit at the intersection of the gas valve, igniter, flame-sensing electrode and gas supply. In British Columbia, diagnosing or adjusting any of these is gas-fitter work — it requires combustion analysis and manometer gas-pressure testing that, by law, only a licensed gas technician (TSBC-certified) may perform. Repeated DIY reset attempts can flood the combustion chamber with unburned gas. Repeatedly resetting the boiler without fixing the root cause can be unsafe and can cause further damage. Call GasBoilers.ca at 604-359-1081 for a licensed diagnosis.
Is the Vaillant F.28 error code dangerous?
It can be. This fault involves combustion, gas or venting. If you ever smell gas, leave the building immediately and call 911 or FortisBC at 1-800-663-9911 from outside. Otherwise, switch the boiler off and book a licensed technician.
How much does it cost to fix Vaillant F.28 in Greater Vancouver?
Cost depends on the root cause and any parts needed. We start with a flat-rate diagnostic, then quote the repair before any work begins — no surprises. Call 604-359-1081 for current pricing and same-day availability.
Look up another brand's error codes
Vaillant showing F.28? We'll fix it right.
Licensed, Red Seal–certified gas technicians across Greater Vancouver. Upfront pricing, same-day service available.